一分彩

新闻

NEWS CENTER

NEWS CENTER

CONTACT US

Contact: Cheng Huiqiang

Cheng Huiqiang:13806256210

Telephone:0512-63982510


Contact:Li Cong

Mobile phone:13962536717

Fax:0512-63982520

Address:No. 333, Jinxian Road, Jinjiaba, FENHU Town, Wujiang District, Suzhou City, Jiangsu Province

Website:www.diendanthanhly.net

Construction grade and technology of polyethylene cold tape for manufacturers of aluminum foil anticorrosive adhesive tape manufacturers

Your current location: Home >> News >> technical knowledge

Construction grade and technology of polyethylene cold tape for manufacturers of aluminum foil anticorrosive adhesive tape manufacturers

Release date:2017-09-12 Author: Click:

Aluminum foil anticorrosive adhesive tape The construction grade and technology of polyethylene cold tape are discussed by manufacturers.

The total thickness (mm) of anticorrosive coating is the structure of anticorrosive layer.

Ordinary grade 0.70 or more, a layer of primer + a layer of inner belt + a layer of outer belt.

Strengthen the grade 1.40 or more of a primer + a layer of 50~55% (with the width of the adhesive tape).

+ a layer of outer belt (50~55% with a tape width).

It is mainly used in oil and natural gas transmission. The external surface anticorrosion of buried steel pipelines such as water supply and drainage and gas transportation in chemical industry and urban construction has the characteristics of convenient construction and no pollution. Polyethylene anticorrosion tape Since 60s, it has been widely used as an external anticorrosive material on oil and gas steel pipelines for more than 40 years. Due to its excellent anticorrosive properties and convenient construction performance, it occupies a certain position in the pipeline anticorrosive material system. And because polyethylene Anticorrosive tape Production enterprises continue to improve and improve the variety and quality of polyethylene tape, so that the application area of polyethylene anticorrosive tape is expanding.

Polyethylene cold tape construction technology:

Surface treatment of steel pipe - priming - tape winding

Pre-processing requirements

1. remove slag, burrs, grease and dirt from the surface of the steel pipe. For pipelines that are heavily overhauled, proper methods should be used to remove the original anticorrosive coating and residue.

2. mechanical or sand blasting and derusting methods (if designated sandblasting treatment), the quality shall meet the national standard "steel surface corrosion grade and derusting grade before painting". GB/T8923-1998 stipulates St3 or Sa2 grade.

3. after derusting, the defects on the surface of the steel pipe should be treated. The dust and abrasives on the surface should be cleaned up and the surface of the steel pipes should be kept dry. When rust or surface contamination occurs, surface pretreatment is necessary.

Primer:
  Aluminum foil anticorrosive adhesive tape

1 the time interval between pretreatment and priming is controlled within 6 hours. The surface of the steel pipe must be dry and dust-free.

2 primer should be evenly stirred in the container. When the primer is thickened, thinner should be added to the primer, so that the viscosity can be constructed when the viscosity is diluted. Primers can be painted with clean brushes, rollers or some other mechanical means.

3 the primer applied to the steel pipe should have no defects such as leak coating, no bubbles, clot and hang. The thickness should be greater than or equal to 30 microns. The welds should be carefully painted to prevent leakage.

4 after the primer is dry, it usually takes 5-10 minutes at room temperature and natural air flow. Special attention should be paid to low temperature or in the construction of trenches, so that the surface drying time should be longer to ensure that the lower part of the steel tube is dry.

5 the time interval between the primer and the tape should be controlled within 8 hours. The surface of the primer should be dry and dust-free. For more than 8 hours or overnight, the primer should be repainted before winding tape.

6 when using primers, attention should be paid to safety, to prevent splash, and to keep away from fire sources. After the primer is used, the remaining primer should be returned to the original iron container and sealed container in time to prevent the volatilization and waste of the primer.

7 under normal circumstances:

Hand painting: 10-12 square meters pipe area / liter primer

Mechanical spraying: 18-20 square meters pipeline area / liter primer Polyethylene anticorrosive adhesive tape manufacturer


Recently viewed:

Suzhou Qiangjiang Pipeline Anticorrosive Material Co., Ltd.

Contact: Cheng Huiqiang

Contact : Li Cong
Telephone:0512-63982510 Mobile phone:13962536717

Mobile phone:13806256210

Fax:0512-63982520
Address: No. 333, Jinxian Road, Jinjiaba, Wujiang District, Suzhou, Jiangsu
Website:www.diendanthanhly.net

Scan